9 replies to this topic

[alecito92]

I wanted to update my android smartphone but got a firmware that was incorrect and now on, the LED does not light and when I connect to load and the computer does not recognize it , I need help

[Jurij]

What incorrect firmware did you flashed? What tool did you used? Any log from that flashing operation?

 

Try to perform deep factory reset:

 

 

Description:
How to do HW reset (forced shut down) for each product is described in the
product?s test instruction (or product manual on the support pages). There are
2 modes of hardware reset in almost all of our products launched 2012 or later
(see exceptions above):

1. Press the HW reset until you get several vibrations, the phone reset and shut down

2. If you do not get any vibration and you continue to press the HW reset, then
after 2 minutes (120s) the phone will perform a very deep HW reset without any
notification! This can solve some rare cases without having to open the unit and
remove and attach the battery connector.

Solution:
If the phone is dead or hanged and do not respond to charger and you don?t get
the vibration doing HW reset, the problem may be solved by continue to press the
reset button for 2 minutes. The long HW reset would solve cases where you don?t
get HW reset vibrations but the unit start after removing and reattaching the
battery connector.

 

 

 Z1 HW Reset.jpg   43.8K   9 downloads

 

then try to flash it with proper firmware using Flashtool: http://sony.yt/topic...oid-smartphone/ .

[alecito92]

try deep restoration works , not work, try flash the phone but when connecting device is not recognized

[faflak]

Start charging the battery

[Jurij]

Yes, battery must be at least 50% charged if you do not want any troubles during flash procedure... 100% is recommended

[alecito92]

where I can find the file for APPWS c6916 , I need to remove it from a hard brick, definitely the phone does not respond to anything

[faflak]

Software download by XperiFirm, or recharge batteries and use the online service

[alecito92]

Software download by XperiFirm, or recharge batteries and use the online service

APPsw need the file extension, not the TFT file.
I 'll make a TEST POINT

[Ksix007]

Hello, friends. I have a Z1S (C6916) and I put a C6903 firmware. Yes, I Know. I did what I should not. Now my phone is Hard Birked. Not into in Fastboot or Flash Mode. So, I search how to unbrick, I followed all the steps but, always diplay this.

25/11/2015 14:00:48 Welcome to S1 tool.
25/11/2015 14:00:48 That is small and crippled subset of SETOOL2 service tool.
25/11/2015 14:00:51  
25/11/2015 14:00:51 SELECT FIRMWARE PACKAGES
25/11/2015 14:00:52 YOU CAN SELECT SEVERAL PACKAGES WITH CTRL BUTTON
25/11/2015 14:01:04 CHECKING PACKAGES ...
25/11/2015 14:01:04  
25/11/2015 14:01:04 DETACH USB CABLE FROM PHONE
25/11/2015 14:01:04 REMOVE BATTERY FROM PHONE
25/11/2015 14:01:04 ATTACH TESTPOINT
25/11/2015 14:01:04 PRESS "READY", THEN ATTACH USB CABLE TO PHONE
25/11/2015 14:01:04  
25/11/2015 14:01:25 will use Sahara protocol ... 
25/11/2015 14:01:25 REMOVE TESTPOINT NOW, THEN PRESS "READY"
25/11/2015 14:01:25  
25/11/2015 14:01:30 PROCESSING ...
25/11/2015 14:01:30 SERIAL NUMBER : 0EBEDB03
25/11/2015 14:01:30 HARDWARE ID : 04000100E1007B00
25/11/2015 14:01:30 PRODUCT DETECTED: "MSM8974 OEM1 fused"
25/11/2015 14:01:30 HASH 0D3C1887A888609DFAE7FCD7A00292B23FD107DC1E02C0956A04DB7B59C71D99 NOT SUPPORTED
25/11/2015 14:01:30 Elapsed:38 secs.

How can I fix my phone?

 

I have TA Backup.

[Jurij]

Buy working phone with broken lcd and swap main board. No other solutions. S1Tool can't flash C6916 phone in s1 emergency mode because we do not have emergency loaders for that model