87 replies to this topic

[jmcr]

Thanks for the steps. I get no vibrate response from phone with hard reset, Vol Up + Power, also no response with button on the back. Phone gives no LED lights or LCD activity or vibrate response.

 

It seems no detection in device manager. I tried to repair with PC Companion, it asks to connect phone into flashmode with Vol Down then USB plug, I do that but PCC/Windows never detects phone.

 

I think it must need stronger tool to save this phone but I'm worried because I don't know how it got bricked. With this method do you have to reload a backup TA? If TA is good will it get overwrite by s1tool or it leaves TA alone? 

[Jurij]

Did you tried to leave your phone on charger for an hour - two? If that will not help, disassembly your phone, connect testpoint to gnd, attach usb cable and flash Xperia ZL firmware in S1 EMERGENCY MODE in order:

 

1. APPSW,

 

2. FSP,

 

3. ELABEL.

 

Phone will be flashed, boot will be updated (if required). And post results

[patica]

Help. I can't repair boot sony c6502 error while uploading final HDR block
 

Welcome to S1 tool.
That is small and crippled subset of SETOOL2 service tool.

SELECT FIRMWARE PACKAGES
YOU CAN SELECT SEVERAL PACKAGES WITH CTRL BUTTON
CHECKING PACKAGES ...

DETACH USB CABLE FROM PHONE
REMOVE BATTERY FROM PHONE
ATTACH TESTPOINT
PRESS "READY", THEN ATTACH USB CABLE TO PHONE

will use DLOAD protocol ...
0808010600900000
0D0F50424C5F446C6F6164564552322E30
162001000100
17004001000100E1907100
PRODUCT DETECTED: "SONY APQ8064-3 ES1 OEM1 Fused"
1801001EA8B0C1B209C88CBB3E220F0AC00F6E6520A273D516B40E7F2EAEB0E5B3DB8B
PROCESSING ...
REMOVE TESTPOINT NOW, THEN PRESS "READY"

Emergency loader uploaded ...

RUNNING S1_PRELOADER VER "APQ8064_39"
LOADER AID: 0001
DEVICE ID: 01CB5B08
FLASH ID: "0011/01000010"
LOADER VERSION: "APQ8064_39"

WRITING PACKAGES ...
Processing package
C:\Users\Refresh\Desktop\C6502\C6502\10_5_A_0_230.APP_SW_Odin_GENERIC_1266_7597_S1_SW_LIVE_5CA3_PID1_0002_MMC.SIN_FILE_SET

MINOR ERROR [ 0x80080021_, err: 0017 ]
error while uploading final HDR block
Break.
FINISHED
Elapsed:210 secs.

[Jurij]

It's hardware problem, you can't fix your phone with any software. Buy working Xperia ZL with broken screen and swap main board.

[patica]

It's hardware problem, you can't fix your phone with any software. Buy working Xperia ZL with broken screen and swap main board.

thank you.

[Ninloth]

Hello folks!
 
I recently got a not working Xperia ZL from a friend. He said the phone was not turning on, just a flash in the boot, and I tried to solve the problem. The phone was starting only with charger, showing the Sony logo, and then restarting indefinitely. When connected to PC, enters in flash mode for some seconds and the starts the reboots. PC Companion does not detect is, and the system was detecting it as S1 Service. Flashtool was not able to do anything either.
 
Unfortunately, all that I was able to find in solving the issue (I did a thorough research in xda and other sites) did not work. Until I find this place.

Following the instructions and videos in the website, I was able to open the phone, get access to the board, and using the pictures provided from @vinaytoday I found the test points, cell detected as QHUSB_DLOAD, downloaded the image from here and used S1 to do the emergency repair. All worked fine, PC Companion did locate the device and I was able to flash an image it with Flashtool.

The case is: even all being fine, the phone just maintain the same problem! After that I thought it could be battery, but I made an external recharge and all is the same. Do you guys have some clue for me to follow? The cell are not in warranty anymore so I am able to do anything with it.

[Jurij]

If you flashed your phone properly (output log from s1tool flashing is always welcome) and phone still reboots by itself, it must be hardware problem. Maybe rehot / reball of flash ic / ram will help...

[prince49]

hey i used the same step you described. my fone is recognised as qhsusb_dload but when i connect after clicking testpoint ready button it shows error:

 

Welcome to S1 tool.
That is small and crippled subset of SETOOL2 service tool.
SELECT FIRMWARE PACKAGES
YOU CAN SELECT SEVERAL PACKAGES WITH CTRL BUTTON
CHECKING PACKAGES ...
DETACH USB CABLE FROM PHONE
REMOVE BATTERY FROM PHONE
ATTACH TESTPOINT
PRESS "READY", THEN ATTACH USB CABLE TO PHONE
llbug: [\\?\USB#Vid_0fce&Pid_d18b#5&111652ef&0&5#{a5dcbf10-6530-11d2-901f-00c04fb951ed}] open error: "A device attached to the system is not functioning"
Elapsed:17 secs.

please help

[Jurij]

Try different usb port, try differrent usb cable, do not use usb 3.0 port. If that will not help, before attaching usb cable insert battery.

[prince49]

Thanks for your help man
My Xperia zl has reborn

[edocomsel]

Thanks for your help man
My Xperia zl has reborn

 

how you do that?

[Jurij]

Just read whole thread and follow described solutions step by step and you will fix your Xperia ZL if boot / firmware is damaged.

[Sirelectro]

I have problem with my hard bricked ZL C6503. 
I Unlocked bootloader with official Sony method. After that my partition table of data partition was damaged and i got bootloop. so i made a new partition for /data. Now it could be formatted in TWRP and i flashed my backup of my rom. Everything was fine until i pressed reboot system. Now Phone is completley dead. 

Phone was detected as qhusb_dload device without testpoint and after driver install as ZEUS FLASH DEVICE. 
I tested to flash with s1tool and after first step it is detected as SEMC FLASH DEVICE. But then i get the error 
can't get S1 command header. See screenshot. I don't really know where the Testpoint of C6503 is . Testpoint from picture doesn't change anything.. 
Tested on multiple computers with windows 7 and 8 64 bit and USB 2.0 port

Attached Files

•  zlflash.png   645.14K   3 downloads

[Jurij]

Loader is not responding. When S1tool will ask you to remove testpoint - remove it, attach battery and press ready button. If that will not help, buy working xperia ZL with broken LCD and swap main board. 

[rahulg]

sir after update my xperia zl c6502 cant power on if press power button red color led blinks three times. I followed ur instructions dissambled my phone, find and attach test points. Aftre i update ur package in emergency mode it will shown in picture. it completed after it cant flasing in flash tool it strucks in 0% what can i do..........

Attached Files

•  001.jpg   215.94K   2 downloads
•  002.jpg   249.52K   2 downloads
•  003.jpg   286.84K   1 downloads

[Jurij]

Boot in your phone is updated so you must flash now all firmware parts.

 

1. Use PC Companion to flash your phone with latest firmware or,

 

2. Use Flashtool and flash your phone with all firmware parts: http://sony.yt/topic...oid-smartphone/ ,

 

3. Or you can use S1Tool to flash all firmware parts in order: APPSW, FSP, ELABEL,

 

4. Or you can purchase flash service in our online service and your phone will be flashed using any Xperia ZL C6502 firmware you want using professional service tool or if you do not have charged battery - using S1Tool in emergency mode. If you need more information please contact me on private message: click or via skype chat: gen.jurij

[vejjus]

Thank you, man! you saved my phone .                                     

[michi123]

hey guys,

 

im lucky, my zl is still working ! im reading this thread cuz im interested in.

but there is a question i´ve to ask:

 

you said:

connect each golden point on main board one by one to metal shield and attach usb cable

so do i´ve to cut an usb-cable to get the braids and skin the cables? or how do you mean that exactly?

 

thx for answering me, i appreciate it!

 

greetz Mike

[Jurij]

so do i´ve to cut an usb-cable to get the braids and skin the cables? or how do you mean that exactly?

 

No, do not cut anything! To perform Xperia ZL testpoint procedure just connect those 2 points together: http://sony.yt/topic...06/#entry43596?using metal paperclip or testpoint wire and attach usb cable to your PC and phone

[ahmed19944]

please help me sir  Jurij