25 replies to this topic

[Sourav9]

Welcome to S1 tool.
That is small and crippled subset of SETOOL2 service tool.


SELECT FIRMWARE PACKAGES
YOU CAN SELECT SEVERAL PACKAGES WITH CTRL BUTTON
CHECKING PACKAGES ...


DETACH USB CABLE FROM PHONE
REMOVE BATTERY FROM PHONE
ATTACH TESTPOINT
PRESS "READY", THEN ATTACH USB CABLE TO PHONE


will use DLOAD protocol ... 
0808010600900000
0D0F50424C5F446C6F6164564552322E30
162001000100
17004001000100E1108800
1801000F43240892D02F0DC96313C81351B40FD5029ED98FF9EC7074DDAE8B05CDC8E1
PHONE NOT SUPPORTED IN THIS MODE
Elapsed:22 secs.

 

 not support.jpg   91.09K   3 downloads

pls help me

somebody help me my c5302 is dead

 

Jurij: I've moved your thread to the correct forum.

[Jurij]

Please tell me what happened that your phone become a dead brick? You can try to flash it (update boot) using the latest s1tool:  s1tool08072014.zip   3.28MB   1653 downloads and post results

[Sourav9]

Welcome to S1 tool.
That is small and crippled subset of SETOOL2 service tool.


SELECT FIRMWARE PACKAGES
YOU CAN SELECT SEVERAL PACKAGES WITH CTRL BUTTON
CHECKING PACKAGES ...


DETACH USB CABLE FROM PHONE
REMOVE BATTERY FROM PHONE
ATTACH TESTPOINT
PRESS "READY", THEN ATTACH USB CABLE TO PHONE


will use DLOAD protocol ... 
0808010600900000
0D0F50424C5F446C6F6164564552322E30
162001000100
17004001000100E1108800
1801000F43240892D02F0DC96313C81351B40FD5029ED98FF9EC7074DDAE8B05CDC8E1
PHONE NOT SUPPORTED IN THIS MODE
Elapsed:37 secs.

 

 

same with s1tool08072014.zip

actually it happened that some how the cord of my wall socket charger got shot during charge and after that the screen of my xperia sp c5302 gone red to black .

after that i tried to power on but every time the red light blink but nothing happens.

I google it and at last I find your post and following it. but the result is here.

i tried Sony PC Companion 2.1 and Flashtool Version 0.9.18.4 but nothing happens.

 

pls help me

sorry for my bad english

thank you

Attached Files

•  latest s1tool.jpg   88.27K   5 downloads

[Jurij]

 

after that i tried to power on but every time the red light blink but nothing happens.

 

Can't you just use different charger or try to charge it via PC and USB cable?

 

 

cord of my wall socket charger got shot during charge

 

What do you mean by that?

[Sourav9]

I used different charger and try to charge it via PC and USB cable but same it remains red light and no screen

 

wire of my wall socket charger was like that

 

• can't power on after that,
• no lcd and red led blinking for power button,
• no lcd and red led on and turn off after a few minute for charger,
• no lcd and red led on and turn off after a few minute and turn on if phone is connected to PC,
• my PC can't detect your phone with vol-,
• phone does not vibrate when holding vol+ and power together.

 

Attached Files

•  wire.jpg   92.57K   5 downloads

Edited by Sourav9, 19 January 2015 - 09:22.

[Jurij]

It's not original Sony usb cable. Please use original Sony accesories (like Sony EP 800 charger). I can see two reasons of not working phone:

 

1. Damaged charger can't charge your phone (discharged phone can't power on) or:

 

2. Damaged charger burned your phone's main board (because of short circuit etc.).

 

Solutions:

 

1. In the first case - use original Sony charger.

2. In the second case - go with your phone to the nearest service centre. They will swap battery and check if phone is working. The most expensive way of repair: buy working xperia SP with broken LCD and swap main board.

 

This tutorial is for software - damaged phones. You can't damage software by charging your phone

[Sourav9]

but my xperia shows in device manager

Attached Files

•  usb.jpg   14.85K   7 downloads

[Jurij]

And what happens when you connect usb cable? It should start charging. Also please tell me what happens when you try to power it on.

[Sourav9]

when I connect usb cable and charger it's not charging, though I don't know because there is no charging signal on screen, only red led turn on for around five minutes and turn off after a few minute for charger, and same happens

no lcd signal and red led on and turn off after a few minute and turn on if phone is connected to PC,

when i try to power it on there is no lcd signal, only the red led is blinking when I press power button.

[Jurij]

Well, try to hold vol+ and power, when phone will vibrate - try to power it on. If that will not help, leave it on the charger for a few hours.

[Sourav9]

when i try to power it on hold and pressing vol+ or vol- and power, every time the red led is blinking but there is no vibration.

I leave it on the charger for 6 to 8 hours with another sony original c5302 charger but it remains same.

[Jurij]

Please download this Sony Xperia SP service manual: http://sony.yt/topic...kcja-serwisowa/. Open test instruction pdf and read page 25 and 26. There is shown how to make hard reset using reset button and what to do to solve charging problems.

[Sourav9]

thanks

 

I'm downloading this file

[fahrul]

excuse me mr jurij, igot trouble like mr Sourav, but my xperia SP c5302 got brick because i wrong to repair when my phone is only bootloop, but i used S1tool, after that my phone brick cannot light or vibrate, please help me. when repeat, the result is PHONE NOT SUPPORTED IN THIS MODE, im sory if my english is bad. thanks hope you help me,   

[Jurij]

Try to flash your phone using the latest s1tool: http://sony.yt/topic...ool/#entry43748. What device can you see in device manager when testpoint and usb cable is connected?

 

 

but my xperia SP c5302 got brick because i wrong to repair when my phone is only bootloop

 

Please tell me what exactly did you tried to do to fix your phone?

[fahrul]

my phone has bootloop, because i restart wit button off when i install ROM cyannogen, but it take long time not finished, then i press off button in behind, exactly my phone display only sony logo, and i search internet how to repair this. and i got your thread i follow your thread, and i was wrong , i mustly take a flashtool no s1tool, but it was happen. and my phone dead not response except when i connected to pc this phone detected by QHSUSB_DLOAD . i tried flash again the result is PHONE NOT SUPPORTED IN THIS MODE, can you tell my why? and can i repair my phone again? thanks (sorry my english is bad)

[Jurij]

 

my phone has bootloop, because i restart wit button off when i install ROM cyannogen, but it take long time not finished, then i press off button in behind, exactly my phone display only sony logo,

 

That's very common mistake, it's easy to brick your phone when you are playing with custom firmwares from xda.

 

 

and i search internet how to repair this. and i got your thread i follow your thread, and i was wrong , i mustly take a flashtool no s1tool, but it was happen.

 

Flashtool will not help you if boot is damaged and phone can't be flashed. S1Tool can't damage your phone. If phone is not supported - it's just not supported. If it's supported - you can flash boot and firmware in normal or dload emergency mode. Maybe you've killed your phone by connecting testpoint not properly?

 

 

and my phone dead not response except when i connected to pc this phone detected by QHSUSB_DLOAD

 

Good.

 

 

i tried flash again the result is PHONE NOT SUPPORTED IN THIS MODE, can you tell my why?

 

Did you tried to flash anything? Do you have any logs from previous operations? My advice is:

 

1. Follow steps from this tutorial: http://sony.yt/topic...303-c5306-m35h/and flash Xperia SP Boot, then firmware in order:

 

a) APPSW,

b) FSP,

c) ELABEL.

 

2. If that s1tool will not work for you, try this one:  s1tool08072014.zip   3.28MB   1653 downloads - it's the latest available version of S1tool.

 

If both versions will not work for you you have two solutions:

 

1. Contact mr the_laser on Setool2 support forum - maybe he will help you. If not:

 

2. Buy working Xperia SP with broken LCD and swap main board. And next time think twice before touching firmwares from xda...

 

 

The sad truth is most of tutorials on xda is not telling the all steps. For example usually when you will flash custom firmware, you must wipe dalvik, cache etc. There is no instructions to do that, because developers usually know that. Most people don't. And phone hangs on logo or does not power on anymore.That's why there is so many damaged phones after flashing custom firmwares...

[fahrul]

but my xperia shows in device manager

Welcome to S1 tool.
That is small and crippled subset of SETOOL2 service tool.




SELECT FIRMWARE PACKAGES
YOU CAN SELECT SEVERAL PACKAGES WITH CTRL BUTTON
CHECKING PACKAGES ...


DETACH USB CABLE FROM PHONE
REMOVE BATTERY FROM PHONE
ATTACH TESTPOINT
PRESS "READY", THEN ATTACH USB CABLE TO PHONE


will use DLOAD protocol ... 
0808010600900000
0D0F50424C5F446C6F6164564552322E30
162001000100
17004001000100E1108800
1801000F43240892D02F0DC96313C81351B40FD5029ED98FF9EC7074DDAE8B05CDC8E1
PHONE NOT SUPPORTED IN THIS MODE
Elapsed:10 secs.

 

 

 

 

 

 

 

 

yes, i was take all your tutorial in your thread and the result like above, yes i know, that sad truth. but im very thanks with your responses, 

Edited by faflak, 31 January 2015 - 08:52.

[Jurij]

Also using S1tool version 08072014? If yes, you have two solutions left:

 

 

 

1. Contact mr the_laser on Setool2 support forum - maybe he will help you. If not:

 

2. Buy working Xperia SP with broken LCD and swap main board. And next time think twice before touching firmwares from xda...

 

 

I can ask the_laser if there is anything he can do with that phone if you want...

[fahrul]

yes i want, but what must i do. can you tell me how to attach a pict in this thread, sorry im new in here